This command displays switch configuration information. If you do not use any of the optional parameters, this command displays global storm control configuration parameters:
- Broadcast Storm Recovery Mode may be enabled or disabled. The factory default is disabled.
- 802.3x Flow Control Mode may be enabled or disabled. The factory default is disabled.
Use the all keyword to display the per-port configuration parameters for all interfaces, or specify the unit/slot/port to display information about a specific interface.
| Format | show storm-control [all | unit/slot/port] |
| Mode | Privileged EXEC |
| Parameter | Definition |
|---|---|
| Bcast Mode | Shows whether the broadcast storm control mode is enabled or disabled. The factory default is disabled. |
| Bcast Level | The broadcast storm control level. |
| Mcast Mode | Shows whether the multicast storm control mode is enabled or disabled. |
| Mcast Level | The multicast storm control level. |
| Ucast Mode | Shows whether the Unknown Unicast or DLF (Destination Lookup Failure) storm control mode is enabled or disabled. |
| Ucast Level | The Unknown Unicast or DLF (Destination Lookup Failure) storm control level. |
Example: The following shows example CLI display output for the command.
(Routing) #show storm-control Broadcast Storm Control Mode................... Disable Broadcast Storm Control Level.................. 5 percent Broadcast Storm Control Action................. None Multicast Storm Control Mode................... Disable Multicast Storm Control Level.................. 5 percent Multicast Storm Control Action................. None Unicast Storm Control Mode..................... Disable Unicast Storm Control Level.................... 5 percent Unicast Storm Control Action................... None
Example: The following shows example CLI display output for the command.
(Routing) #show storm-control 1/0/1
Bcast Bcast Bcast Mcast Mcast Mcast Ucast Ucast Ucast
Intf Mode Level Action Mode Level Action Mode Level Action
------ ------- -------- ---------- ------- -------- ---------- ------- -------- ----------
1/0/1 Disable 5% None Disable 5% None Disable 5% None
Example: The following shows an example of part of the CLI display output for the command.
(Routing) #show storm-control all
Bcast Bcast Bcast Mcast Mcast Mcast Ucast Ucast Ucast
Intf Mode Level Action Mode Level Action Mode Level Action
------ ------- -------- ---------- ------- -------- ---------- ------- -------- ----------
1/0/1 Enable 50 Trap Disable 5% None Disable 5% None
1/0/2 Enable 50 Trap Disable 5% None Disable 5% None
1/0/3 Enable 50 Trap Disable 5% None Disable 5% None
1/0/4 Enable 50 Trap Disable 5% None Disable 5% None
1/0/5 Enable 50 Trap Disable 5% None Disable 5% None
1/0/6 Enable 50 Trap Disable 5% None Disable 5% None
1/0/7 Enable 50 Trap Disable 5% None Disable 5% None
1/0/8 Enable 50 Trap Disable 5% None Disable 5% None
1/0/9 Enable 50 Trap Disable 5% None Disable 5% None
1/0/10 Enable 50 Trap Disable 5% None Disable 5% None
1/0/11 Enable 50 Trap Disable 5% None Disable 5% None
1/0/12 Enable 50 Trap Disable 5% None Disable 5% None
1/0/13 Enable 50 Trap Disable 5% None Disable 5% None
1/0/14 Enable 50 Trap Disable 5% None Disable 5% None
1/0/15 Enable 50 Trap Disable 5% None Disable 5% None
1/0/16 Enable 50 Trap Disable 5% None Disable 5% None
1/0/17 Enable 50 Trap Disable 5% None Disable 5% None
1/0/18 Enable 50 Trap Disable 5% None Disable 5% None
1/0/19 Enable 50 Trap Disable 5% None Disable 5% None
